Quick Support Tooling fabrication course in repair of composite and metal bonded Aircraft parts

Course code:  TECH-171 (Stage I)

Course duration: 5 Day

Introduction: 
This is our Quick Repair support tooling fabrication course (Stage I) which is developed for personnel of technical departments, MRO stations or AOG service stations
who want learn to fabricate Quick support tooling for aircraft composite and metal bonded parts to stabilize while being repaired at elevated temparatures 

Advised Pre Requisites
Our EFC Courses, TECH-001, TECH-010 or TECH-020 (Stage I to 3 ) can be a prerequisite. or 2-3  year repair experience on aircraft composite parts is required for this course, or an equivalent level. If in doubt, contact us to assess your equivalent level of knowledge and skills needed for this course.

Participants
Personnel of technical departments, MRO stations, AOG services such as Composte Reapir technicians, certifying staff, engineers and others.

Number of participants:  Minimum 4, Maximum 12 participants per course*.
* A definitive course date will be set by EFC as soon as sufficient applications are received! Subscribers will be informed instantly.

Objectives
Upon completion of this course the participant:

  • Has a better knowledge of  quick composite tool design and fabrication in upport
  • Has knowledge and skills of surface preparation of an existing part
  • Is familiar with Tool lay-up sequence, balance and symmetry
  • Is familiar with tool
  • Can re-claim the part surface
  • Can install tool index and trim fixtures
  • Can fabricate & apply quick repair tooling on metal bonded structure parts
  • Can fabricate & apply quick repair tooling on fiber reinforced composite parts 
  • Knows how to use and work with wax sheet to offset ply thickness
  • Can apply vacuum bags and use of a pleat for quick repair tooling
  • Will have advanced knowledge and skills to apply of Low Temperature Moulding (LTM) materials

Content Theory (level 2-3)

  • Damage assessment, Repair plan, Stabilize part and damage,
  • Reclaiming the part surface
  • Coefficient of Thermal Expansion (CTE) and spring back correction of return flanges
  • Tool Heat transfer and tool materials use
  • Coefficient of expansion of composite material used at room temp. and high temp cures. 
  • Remove of fasteners
  • Extending part flanges and support structure for existing part
  • Use of template to reclaim fastener holes,
  • Ply table use 
  • Drill bushings for fastener hole reclaiming
  • Use of Plier operated Hex-nut Cleco fasteners, Wing nut cleco fasteners, skin pins 
  • Fabrication  Quick Repair Support Tooling for Metal Bonded Structure
  • RT or Low Temp. cure WLU resins & Post cures
  • Tool index features
  • Tool support structure
  • Tool leak frames incorperated in return flanges
  • Mould tool joggle lay-up
  • Tooling wax sheet use for offset edges
  • Cotton Felt Tooling use  for repair area support
  • Attachment of wet Lay-up cleats
  • Use and fabrication of pre-cured tool inserts
  • Application of de-bulks pleat installation in vacuumbags
  • Cure and Post-cue cycle temperatures versus tool life cycle
  • Tool trimming
  • One-off tooling 
  • Applications of Quick Repair Tooling
  • Application and types of fast applicable composite tooling sealers and release agents 

Workshop (Level 3)
The participant will be able to:

  • Assess damage, create a repair plan, 
  • Reclaiming the part surface
  • Stabilize damage, 
  • Make fastener templates, reinforcements, 
  • Extend existing flanges of a part
  • Stabilize flanges, drill templates
  • Apply fences for return flanges
  • Apply wax sheets and determine wax radii
  • Apply tool index features 
  • Apply LTM tooling material
  • Be able to program  hotbonder to  monitor heatlamps, ceramic heaters and parameters for cure or post-cure cycles.

Examination

  • Multiple choice questions from each of the teachings Levels 2-3
  • Successful completion is 75% correct answers (The examination is closed book)
  • The practical mark will be the average of all marks gained from the practical exercises 
  • A full participant practical logbook will be presented to the participant and/or company.
  • All grades will be recorded in the participant individual training records and kept on record at EFC a for unlimited time (compliant with Reference EASA Commission Regulation (EU) No 1321/2014)

Request for running this course anytime
This course can be requested when required and is not limited to the upcomg course dates shown on this website.
Please do contact us as shown below.

'On-Site' Training

It can also be requsted for an 'On-Site' training at your company under certain "Terms & Conditions"

It will involve additional cost such as: Instructor(s) Travel, lodging, daily allowance, shipping /ensuring material and bringing in equipment.

To hold this course 'On-Site' successfully, there are specific material and equipment requirements that need to be present at your company. Ask us for our 'On Site' training requirement document for more specific information what is needed to run this course.

Note for companies only:

  • If required, our Training course can be tailored made to meet your specific needs. 
  • Course dates as noted on our schedule can be adjusted on request to a required starting date.

For information & requirements, contact our business & purchasing manager Rolf Hovener via e-mail at r.a.hover@efcomposites.com or owner / Founder Bert Groenewoud via e-mail at info@efcomposites.com

Course pricing
All listed course prices are Excl. VAT. Dutch VAT is 21% (comparable with VAT). EFC complies with Dutch tax laws. Companies on request receive an invoice instead of paying on-line with PayPal, IDEAL or credit card.